homelabhome assistantunifi
The Chandelier Bulb Fix
Sixteen smart bulbs in a TV-room chandelier, randomly half-offline for months — diagnosed live, and fixed without replacing a single bulb (yet). October 16, 2026.
The setup
A large chandelier in the TV room holds 16 Lightinginside Smart E12 LED candle bulbs (Tuya/SmartLife, 2.4 GHz WiFi). They're grouped in Home Assistant as TV Chandelier and also exposed to Google Home.
The complaint: at any given moment only 3 or 4 bulbs would respond. The rest showed offline — a different random subset every time, despite the fixture being close to a UniFi access point.
What the diagnosis found
- They're cloud bulbs, not Matter. In Home Assistant all 16 run on the Tuya cloud integration, and Google Home reaches them through the SmartLife cloud too. One dropped cloud heartbeat = offline in every app at once.
- At check time, 3 of 16 were available in Home Assistant — exactly matching the reported symptom.
- The WiFi link was marginal. Most bulbs had associated to an older nanoHD in the guest room at −61 to −75 dBm, with thousands of transmit retries on nearby radios. The two bulbs that happened to land on the WiFi 6 AP in the family room sat at −46/−47 dBm. Sixteen tiny radios clustered inside one big fixture, all on a single 2.4 GHz channel, is a rough RF neighborhood — "close to the AP" in feet, not in link budget.
- The fixture is on a Forbes & Lomax dimmer. Smart bulbs need constant full voltage; a dimmer feeds them a chopped waveform and can brown out their radios even near max. That alone causes random drop-and-rejoin behavior — and bulb makers (Philips Hue included) say not to run smart bulbs on dimmers at all.
- The bulbs were invisible in UniFi. Their radios all report the hostname
lwip0with no name, so the controller showed 16 identical anonymous clients — impossible to select, let alone pin to an AP.
The fix
1. Made the bulbs visible. Identified the 16 clients by their hardware (MAC) prefix and renamed them in the UniFi controller: TV Chandelier 01–16.
2. Pinned them to the right AP. Locked all 16 bulbs to the U6 Fam-room access point (UniFi "Lock to Access Point"), so they can't drift back to the weaker guest-room AP.
3. Maxed the dimmer trim on the Forbes & Lomax dimmer (done at the wall), giving the bulbs the cleanest power that circuit can offer.
Early results
| Metric | Before | After pinning |
|---|---|---|
| Signal, typical bulb | −61 to −75 dBm (guest-room nanoHD) | −43 to −53 dBm (U6 Fam-room) |
| AP the bulbs chose | Mostly the older AP, ch 1 | Locked to the WiFi 6 AP |
| Findable in UniFi | 16 anonymous "lwip0" clients | TV Chandelier 01–16 |
Bulbs re-home over a few minutes after pinning (their radios retry slowly), so the full 16 settle in gradually rather than all at once.
If they still misbehave
- Swap the dimmer module for a plain Forbes & Lomax switch in the same plate/finish, and let the bulbs dim digitally. This is the permanent fix for the power side.
- Replace the bulbs with a mesh system. Zigbee or Thread bulbs repeat for each other, stay off WiFi, and drop the cloud entirely. Priced options for 16 bulbs: Philips Hue E12 color — $55/bulb in 2-packs, ≈ $880 all-in, drops onto the existing Hue Bridge; IKEA KAJPLATS E12 (Matter-over-Thread) — $9.99/bulb, ≈ $160, needs a Thread border router.